国产成人v爽在线免播放观看,日韩欧美色,久久99国产精品久久99软件,亚洲综合色网站,国产欧美日韩中文久久,色99在线,亚洲伦理一区二区

學習啦>學習電腦>網絡知識>路由器>路由器設置>cisco思科>

思科跨路由器的單臂路由如何解決

時間: 權威724 分享

  思科擁有豐富的行業經驗、先進的技術,路由器功能也在世界遙遙領先,那么你知道思科跨路由器的單臂路由如何解決嗎?下面是學習啦小編整理的一些關于思科跨路由器的單臂路由如何解決的相關資料,供你參考。

  思科跨路由器的單臂路由解決的方法

  R1配置:

  R1#conf t

  R1(config)#int f0/0

  R1(config-if)#no shutdown

  R1(config-if)#int f0/0.2

  R1(config-subif)#encapsulation dot1q 2

  R1(config-subif)#ip address 192.168.2.254 255.255.255.0

  R1(config-subif)#no shutdown

  R1(config-subif)#exit

  R1(config)#int f0/0.3

  R1(config-subif)#encapsulation dot1q 3

  R1(config-subif)#ip address 192.168.3.254 255.255.255.0

  R1(config-subif)#no shutdown

  R1(config-subif)#exit

  R1(config)#int s1/0

  R1(config-if)#ip address 1.1.1.1 255.255.255.0

  R1(config-if)#no shutdown

  R1(config-if)#end

  R1#conf t

  R1(config)#router ospf 1

  R1(config-router)#network 192.168.2.0 0.0.0.255 area 0

  R1(config-router)#network 192.168.3.0 0.0.0.255 are 0

  R1(config-router)#network 1.1.1.0 0.0.0.255 area 0

  R1(config-router)#end

  R2配置:

  R2#conf t

  R2(config)#int s0/0

  R2(config-if)#ip address 1.1.1.2 255.255.255.0

  R2(config-if)#no shutdown

  R2(config-if)#clock rate 64000

  R2(config-if)#exit

  R2(config)#int s0/1

  R2(config-if)#ip address 2.1.1.1 255.255.255.0

  R2(config-if)#no shutdown

  R2(config-if)#clock rate 64000

  R2(config-if)#end

  R2#conf t

  R2(config)#router ospf 2

  R2(config-router)#network 2.1.1.0 0.0.0.255 area 0

  R2(config-router)#network 1.1.1.0 0.0.0.255 area 0

  R2(config-router)#end

  R3配置:

  R3#conf t

  R3(config)#int s1/0

  R3(config-if)#ip address 2.1.1.2 255.255.255.0

  R3(config-if)#no shutdown

  R3(config)#int f0/0

  R3(config-if)#no shutdown

  R3(config-if)#int f0/0.2

  R3(config-subif)#encapsulation dot1q 2

  R3(config-subif)#ip address 172.16.2.254 255.255.255.0

  R3(config-subif)#no shutdown

  R3(config-subif)#exit

  R3(config)#int f0/0.3

  R3(config-subif)#encapsulation dot1q 3

  R3(config-subif)#ip address 172.16.3.254 255.255.255.0

  R3(config-subif)#no shutdown

  R3(config-subif)#end

  R3(config)#router ospf 3

  R3(config-router)#network 172.16.2.0 0.0.0.255 area 0

  R3(config-router)#network 172.16.3.0 0.0.0.255 area 0

  R3(config-router)#network 2.1.1.0 0.0.0.255 area 0

  R3(config-router)#end

  查看路由表:

  R1#show ip route

  Gateway of last resort is not set

  1.0.0.0/24 is subnetted, 1 subnets

  C 1.1.1.0 is directly connected, Serial1/0

  2.0.0.0/24 is subnetted, 1 subnets

  O 2.1.1.0 [110/128] via 1.1.1.2, 00:03:37, Serial1/0

  172.16.0.0/24 is subnetted, 2 subnets

  O 172.16.2.0 [110/129] via 1.1.1.2, 00:03:37, Serial1/0

  O 172.16.3.0 [110/129] via 1.1.1.2, 00:03:37, Serial1/0

  C 192.168.2.0/24 is directly connected, FastEthernet0/0.2

  C 192.168.3.0/24 is directly connected, FastEthernet0/0.3

  R2#show ip route

  Gateway of last resort is not set

  1.0.0.0/24 is subnetted, 1 subnets

  C 1.1.1.0 is directly connected, Serial0/0

  2.0.0.0/24 is subnetted, 1 subnets

  C 2.1.1.0 is directly connected, Serial0/1

  172.16.0.0/24 is subnetted, 2 subnets

  O 172.16.2.0 [110/65] via 2.1.1.2, 00:03:37, Serial0/1

  O 172.16.3.0 [110/65] via 2.1.1.2, 00:03:37, Serial0/1

  O 192.168.2.0/24 [110/65] via 1.1.1.1, 00:03:37, Serial0/0

  O 192.168.3.0/24 [110/65] via 1.1.1.1, 00:03:37, Serial0/0

  R3#show ip route

  Gateway of last resort is not set

  1.0.0.0/24 is subnetted, 1 subnets

  O 1.1.1.0 [110/128] via 2.1.1.1, 00:03:43, Serial1/0

  2.0.0.0/24 is subnetted, 1 subnets

  C 2.1.1.0 is directly connected, Serial1/0

  172.16.0.0/24 is subnetted, 2 subnets

  C 172.16.2.0 is directly connected, FastEthernet0/0.2

  C 172.16.3.0 is directly connected, FastEthernet0/0.3

  O 192.168.2.0/24 [110/129] via 2.1.1.1, 00:03:43, Serial1/0

  O 192.168.3.0/24 [110/129] via 2.1.1.1, 00:03:43, Serial1/0

  SW1配置:

  SW1#vlan database

  SW1(vlan)#vlan 2

  SW1(vlan)#vlan 3

  SW1(vlan)#exit

  SW1#conf t

  SW1(config)#int f0/15

  SW1(config-if)#switchport mode trunk

  SW1(config-if)#switchport trunk encapsulation dot1q

  SW1(config-if)#exit

  SW1(config)#int f0/2

  SW1(config-if)#switchport mode access

  SW1(config-if)#switchport access vlan 2

  SW1(config-if)#exit

  SW1(config)#int f0/3

  SW1(config-if)#switchport mode access

  SW1(config-if)#switchport access vlan 3

  SW1(config-if)#end

  SW2配置:

  SW2#vlan database

  SW2(vlan)#vlan 2

  SW2(vlan)#vlan 3

  SW2(vlan)#exit

  SW2#conf t

  SW2(config)#int f0/15

  SW2(config-if)#switchport mode trunk

  SW2(config-if)#switchport trunk encapsulation dot1q

  SW2(config-if)#exit

  SW2(config)#int f0/2

  SW2(config-if)#switchport access vlan 2

  SW2(config-if)#exit

  SW2(config)#int f0/3

  SW2(config-if)#switchport mode access

  SW2(config-if)#switchport access vlan 3

  SW2(config-if)#end

  驗證:

  PC1:

  PC1#ping 192.168.3.3

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 192.168.3.3, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 188/246/300 ms

  PC1#ping 172.16.2.2

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 172.16.2.2, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 408/487/528 ms

  PC1#ping 172.16.3.3

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 172.16.3.3, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 384/441/492 ms

  PC3:

  PC3#ping 172.16.3.3

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 172.16.3.3, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 168/258/348 ms

  PC3#ping 192.168.2.2

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 348/400/452 ms

  PC3#ping 192.168.3.3

  Type escape sequence to abort.

  Sending 5, 100-byte ICMP Echos to 192.168.3.3, timeout is 2 seconds:

  !!!!!

  Success rate is 100 percent (5/5), round-trip min/avg/max = 312/396/516 ms

  看過文章“思科跨路由器的單臂路由如何解決"的人還看了:

  1.思科路由器怎么阻斷局域網病毒傳播

  2.思科路由器怎么設置橋接(bridging)實例

  3.思科路由器控制端口連接圖解

  4.思科路由器怎么進入 思科路由器怎么設置

  5.思科路由器基本配置教程

  6.詳解Cisco(思科)路由器的故障日志

  7.Cisco 路由器訪問權限的設置

  8.如何連接cisco路由器

  9.思科路由器使用IS-IS路由IP的基本設置方法

  10.如何利用腳本配置思科路由器

554617