如何配置思科IOS防火墻
如何配置思科IOS防火墻
思科依靠自身的技術和對網絡經濟模式的深刻理解,使他成為了網絡應用的成功實踐者之一,其制造的路由器也是全球頂尖的,那么你知道如何配置思科IOS防火墻嗎?下面是學習啦小編整理的一些關于如何配置思科IOS防火墻的相關資料,供你參考。
配置思科IOS防火墻的方法:
拓?fù)鋱D
配置思科IOS防火墻步驟
第一步:在R1 、 R2 、 R3上的預配置
r1(config)#int e0/0
r1(config-if)#ip add 172.16.1.1 255.255.255.0
r1(config-if)#no sh
r1(config)#ip route 0.0.0.0 0.0.0.0 172.16.1.2配置靜態路由
r1(config)#^Z
r2(config)#int e0/0
r2(config-if)#ip add 172.16.1.2 255.255.255.0
r2(config-if)#no sh
r2(config-if)#int e2/0
r2(config-if)#ip add 192.168.1.2 255.255.255.0
r2(config-if)#no sh
r3(config)#int e2/0
r3(config-if)#ip add 192.168.1.3 255.255.255.0
r3(config-if)#no sh
r3(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2 配置靜態路由
r3(config)#^Z
r3(config)#li vty 0 4
r3(config-line)#pass
r3(config-line)#password cisco
r3(config-line)#exit
第二步:
在R2上配置zhang
r2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r2(config)#ip inspect name zhang tcp 檢查TCP
r2(config)#ip inspect name zhang udp 檢查udp
r2(config)#ip inspect udp idle-time 60 檢查udp 的時間是60S
r2(config)#ip inspect name zhang icmp timeout 5 超時時間是5S
r2(config)#ip inspect name zhang http alert off 控制HTTP
r2(config)#
r2(config)#int e0/0
r2(config-if)#ip inspect zhang in 在e0/0接口檢查流量是否滿足以上所定義過的任何一條
r2(config-if)#exit
r2(config)#acce 100 deny ip any any log 做ACL拒絕IP的任何包通過
r2(config)#int e2/0
r2(config-if)#ip acce 100 in 將ACL要用到e2/0的進接口上
第三步: 從R1上TELNET R3
r1#telnet 192.168.1.3
Trying 192.168.1.3 ... Open
User Access Verification
Password:
r3>
從R3上TELNET R1
r3#telnet 172.16.1.1
Trying 172.16.1.1 ...
% Destination unreachable; gateway or host down
第四步:
從R1上ping R2直連接口
r1#ping 172.16.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/54/92 ms
從R2上ping R1直連接口
r2#ping 172.16.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/67/124 ms
從R2ping R3直連接口
r2#ping
*Mar 1 00:15:20.615: %SYS-5-CONFIG_I: Configured from console by console
r2#ping 192.168.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
*Mar 1 00:15:28.055: %SEC-6-IPACCESSLOGDP: list 100 denied icmp 192.168.1.3 -> 192.168.1.2 (0/0), 1 packet..... //說明icmp包可以到達,但 是沒有回包
Success rate is 0 percent (0/5)
從R3ing R2連接口
r3#ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
U.U.U //說明icmp包不可以到達目的地
Success rate is 0 percent (0/5)
r1#ping 192.168.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 76/124/156 ms
r2#debug ip inspect icmp
INSPECT ICMP Inspection debugging is on
r2#
*Mar 1 00:35:09.187: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.187: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.191: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.263: CBAC: ICMP Echo Reply pkt 192.168.1.3 => 172.16.1.1
*Mar 1 00:35:09.375: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.423: CBAC: ICMP Echo Reply pkt 192.168.1.3 => 172.16.1.1
*Mar 1 00:35:09.467: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.531: CBAC: ICMP Echo Reply pkt 192.168.1.3 => 172.16.1.1
*Mar 1 00:35:09.563: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
r2#
*Mar 1 00:35:09.623: CBAC: ICMP Echo Reply pkt 192.168.1.3 => 172.16.1.1
*Mar 1 00:35:09.671: CBAC: ICMP Echo pkt 172.16.1.1 => 192.168.1.3
*Mar 1 00:35:09.735: CBAC: ICMP Echo Reply pkt 192.168.1.3 => 172.16.1.1